Power Tool Accessory

(15 products)
View as

The things that go on the end of a drill or a driver: screwdriver bits from 0.150 KD, bit holders, a keyed chuck, wire brushes, a screw extractor set, riveter adapters and a sheet-metal cutting attachment at 7.450 KD. These are not drill bits — for those see drill bits and hole saws. Everything here is in stock, and the bits in particular are held in quantity for trade orders.

Which one do you need?

Type Best for Price
Screwdriver bits — PH1, PH2, PH3, SL6 and Torx T10 to T40 The consumable. 25 mm stubby bits are 0.150 KD, 65 mm are 0.250 KD single-ended and 0.500 KD double-ended, 100 mm are 0.750 KD and 150 mm are 1.000 KD. Torx in T10, T15, T20, T25, T27, T30 and T40 at 65 mm are 0.500 KD. Buy them by the handful — bits are the part that wears 0.150–1.000 KD
Single screwdriver bit A one-off replacement when a bit rounds off mid-job 0.750 KD
Magnetic screwdriver bit, 65 mm Overhead and one-handed work — the magnet holds the screw on the tip so you are not catching it as it falls 1.250 KD
Bit holder with quick release, 60 mm Swapping bits without a chuck key — worth it the moment you are alternating between two screw heads on one job 2.000 KD
Magnetic nut socket, 10 mm or 3/8" Driving hex-head and self-drilling screws into sheet and roofing with a drill instead of a spanner. 0.350 KD for 10 mm, 0.450 KD for 3/8" 0.350–0.450 KD
Drill chuck with key, 13 mm, 3-piece set Replacing a chuck that has stopped gripping, rather than replacing the drill 0.950 KD
Screw extractor set, 5 pieces Getting out a screw whose head has rounded off or snapped. Five sizes, and it is the thing nobody buys until they need it badly 1.500 KD
Wire brush, 4 lines Hand cleaning of rust, weld spatter and old paint 0.300 KD
Cup wire brush with nut, 75 mm The same job done with a machine — screws onto a grinder rather than being held in the hand 0.750 KD
Riveter drill adapter, 2.4 to 4.8 mm Turning a drill into a rivet gun — faster and far less tiring than a hand riveter over a long run of rivets 3.500 KD
Riveter adaptor for a drill A second riveter adapter. Its size range is not recorded, so bring your rivets or ask at the counter before you buy it 5.000 KD
Sheet metal nibbler attachment for a drill Ducting, cladding, gutters and mesh — 183 mm long with an 18 × 8 mm hex shank and a 102 mm side handle, and rated to 1.2 mm iron sheet, 0.9 mm aluminium, 0.6 mm 304 stainless, 2.6 mm PVC and 2.5 mm iron wire. Down to 10 units 7.450 KD

Out of stock at the moment: a riveter nut adapter for a drill, a larger riveter drill adapter kit, and a water tank wrench. Ask us about availability.

What to check before buying

  • Single-ended or double-ended at 65 mm? This is the only step in the bit ladder that is not about length. A 65 mm single-ended bit is 0.250 KD and a double-ended one is 0.500 KD — the extra 0.250 KD buys a second tip, so you flip it instead of replacing it. At these prices the double-ended bit is the better buy if you use the same head all day.
  • Buy bits by the handful. At 0.150 KD for a 25 mm bit, the cost of a bit is nothing next to the cost of stopping. We hold them in quantity — 1,786 across the sizes today — so a trade order is no problem.
  • Length is about reach, not strength. A 25 mm bit in a holder is stiffer and more accurate; a 150 mm bit is for getting down a recess or between studs. Buy short for everyday and long for the awkward one.
  • Get the nut socket, not a spanner, for roofing screws. The 10 mm and 3/8" magnetic sockets at 0.350 and 0.450 KD turn a drill into the right tool for self-drilling screws, and the magnet means you are not holding the screw with your other hand up a ladder.
  • A screw extractor is cheaper than the alternative. At 1.500 KD for five sizes, it is the difference between a ten-minute job and drilling out a fitting. It is worth having in the box before you need it.
  • Lots of rivets to set? The 3.500 KD drill adapter covers 2.4 to 4.8 mm rivets and will outlast your wrist. The rivets themselves are in blind rivets.
  • Looking for drill bits? Different page. Masonry, metal, wood, HSS bits and hole saws are all in drill bits and hole saws.

Buying it from Bab Al-Saif

  • Bring the drill or the screw to our showroom at Shuwaikh Plaza, Khalifa Al-Jassim Street, Shuwaikh Industrial — matching a bit to a screw head, or a chuck to a drill, takes ten seconds at the counter and is guesswork online.
  • In Kuwait since 1992, rated 4.7★ by over 350 customers on Google.
  • Cash on delivery, card, or split your payment with Deema, with delivery across Kuwait.

FAQs

How much are screwdriver bits in Kuwait?

From 0.150 KD for a 25 mm bit. 65 mm bits are 0.250 KD single-ended and 0.500 KD double-ended, 100 mm are 0.750 KD and 150 mm are 1.000 KD. Phillips comes in PH1, PH2 and PH3, there is a slotted SL6, and Torx runs T10, T15, T20, T25, T27, T30 and T40 at 0.500 KD each. All in stock.

Do you have drill bits on this page?

No. These are screwdriver bits, which drive screws. Drill bits make holes, and they are in drill bits and hole saws along with the hole saws — masonry, metal, wood and HSS.

Can I rivet with a drill instead of a hand riveter?

Yes. The 3.500 KD riveter adapter chucks into any drill and sets rivets from 2.4 to 4.8 mm. There is a second adapter at 5.000 KD whose size range is not recorded, so bring your rivets or ask us before buying that one. The rivets are in blind rivets.

What can the drill nibbler attachment cut?

By its own rating: iron sheet and iron mesh to 1.2 mm, aluminium plate to 0.9 mm, 304 stainless to 0.6 mm, 201 stainless to 0.5 mm, coloured steel mesh to 1.1 mm, PVC to 2.6 mm and iron wire to 2.5 mm. It is 183 mm long, takes an 18 × 8 mm hex shank into any drill chuck, and comes with a 102 mm side handle. We have 10 of them.

Also useful: drill bits and hole saws for making the hole, and screwdrivers when a hand tool is the right tool.

Compare /5