Digital Angle Finder Magnetic Level Box 4 Units - BAS Kuwait
Digital Angle Finder Magnetic Level Box 4 Units - BAS Kuwait غير متوفر حاليًا وسيتم شحنه فور توفره في المخزون.
مواصفات المنتج
مواصفات المنتج
تفاصيل التوصيل
تفاصيل التوصيل
نوفر توصيلاً سريعاً وموثوقاً في جميع أنحاء الكويت:
📦 التوصيل العادي – 1.350 د.ك
خلال يومي عمل.
⚡ التوصيل السريع – 2 د.ك
خلال 24 ساعة.
🏠 منتجات المنزل الذكي (مع التركيب)
يُحدَّد موعد التركيب خلال 3 أيام عمل بعد تأكيد الطلب.
نشحن الطلبات ونحدد مواعيد التركيب من السبت إلى الخميس.
✔ إذا شُحن طلبك يوم الخميس، يمكن أن يتم التوصيل يوم الجمعة.
Digital Angle Finder Magnetic Level Box 4 Units - BAS Kuwait غير متوفر حاليًا وسيتم شحنه فور توفره في المخزون.
الوصف
الوصف
A small magnetic box that tells you the exact angle of whatever you stick it to. Put it on a saw blade, a pipe, a bracket, a bed of a machine or a shelf, and it reads the angle to a hundredth of a degree on a backlit screen.
The point of it is that a spirit bubble tells you level or not level. This tells you the number. Setting a mitre saw to 37.5 degrees, checking a fall on a pipe run, matching an existing angle on site, squaring a machine bed: those all need a figure, not a bubble.
Four units, one button
Press UNITS and it cycles through four ways of saying the same thing:
- Degrees. The ordinary angle.
- Percent. Slope as a percentage, the way drainage and ramps are specified.
- mm/m. Metric slope, millimetres of fall per metre.
- in/ft. Imperial slope, inches of fall per foot.
So the same measurement reads out in whatever the drawing in front of you is written in, without arithmetic.
Absolute and relative
ABS reads the true angle from level. Press REF and it zeroes against whatever it is sitting on, so from then on it reads the difference. That is how you copy an existing angle onto a new piece, or check whether two surfaces match, without caring what either one is relative to the floor.
How it is built
- Strong magnets on the base, so it clamps itself to steel and stays put while you adjust.
- Backlit display, readable in a dark corner or under a machine.
- HOLD freezes the reading, for when the box is somewhere you cannot see it.
- Automatic power off after five minutes, so it does not flatten its battery in a toolbox.
- Rubber-armoured body with a solid machined edge for registering against a face.
Accuracy
Measurement accuracy is plus or minus 0.2 degrees, and the display resolves to 0.05 degrees. CAL recalibrates it against a known flat surface whenever you want to be certain.
Buying it from Bab Al-Saif
See it at our showroom in Shuwaikh Plaza, Khalifa Al-Jassim Street, Shuwaikh Industrial. Serving Kuwait since 1992, rated 4.7 stars by over 350 Google reviewers. Pay cash on delivery, by card, or in instalments with Deema. Delivery anywhere in Kuwait.
Questions
Does it have a laser? No. This is the NF-566. The laser version is a different model.
Will it stick to a saw blade? Yes, the base is magnetic and holds on any steel surface.
Can I zero it against an existing angle? Yes, that is what the REF relative mode does.
How accurate is it? Plus or minus 0.2 degrees, displayed to 0.05 degrees.











